Just to begin out, this is no my idea however I simply thought some people might discover it exciting to use without searching the internet. This is a tutorial on how to make among the blasters the the stormtroopers off of starwars have so lets obtain started!You will need some templates for this and they can be downloaded from here:http://www.imperial-fleet.com/BBC/iambubby.zip




You are watching: How to make a star wars blaster

*

You will require a piece of 1 1/4 PVC pipeline 18.5 inch long. (Gray PVC preferably but any type of will do) Templates, target cap and a Hex cap or far better yet here"s an alternative to the Hex cap. If you have actually a LOWE"s close to by choose up a 1 inch Plug, here"s a component number that will make life a lot easier building this blaster, SKU or Barcode# 0-25628-14290-2


*

*

First pre drill every holes with a smaller drill bit then go earlier and drill the holes to the right size. This will take some time come do, however go slow and also take your time, it"s precious it!


*

You may opt to put guts in the blaster, i did this to my very first and I have to say it"s no really precious it. If you execute decide to do the within guts, Feel free to come increase with whatever here. It"s approximately you! I included some brass pipeline the the barrel and a ring rubber item on the opposite end to store it from moving around inside the gun. The fixed is made from Redwood. The butt cap has actually been sanded flat on the end and also all wording ~ above the sides sanded off. The barrel reminder is the Hex cap, sanded come fit inside the barrel. Clean up the grip and sand it to the form desired.


*
*
*
*

Cut and tape the remainder of the templates on everything material you plan to do these with. I used sheet metal and thick aluminum. Use your Dremel or whatever you have to reduced the templates out of the metal. Security First, use security glasses at all times! after cutting every the parts out, make sure to sand or paper the edges. Clean castle up and also get ready to install them.


Install the front and also rear sites. Prep your handle and also install the trigger guard and safety switch. Use your Dremel to make slot in the main real estate for the front vision then epoxy that in. Placed some Epoxy all the means around the outside, this makes it look choose it"s been welded. Usage rivets or screws to affix the behind sight.


This is the BEST way to do the handle! reduced out the templates, trace them top top a piece of sheet Styrene and also cut out, adhesive them every together and this is what you must come increase with! Drill 2 holes in the tight so everything screw you use will on slide through. Respond to sink the two holes therefore the screw is do the washing up or listed below the surface. Be certain to sand the head the the screw to provide the filler something to organize to. Ar the grip in ~ the correct position on the receiver and screw in place. Add some filler to the two screws and also let dry. Sand flush and also you"re done.


You require to cut a small d-ring holder because that the butt cap. Install it through rivets. This prior nozzle pictured will not it is in used! currently take a rest you deserve it.


The front vision is easy. Take a little block that wood and also trim it under to right snug into the vision that"s already mounted on her blaster. Drill a feet in the center and also place one old flat head drill little bit inside. Epoxy, permit dry and also install.


After you obtain the mag housing developed you will notice you have around a 4 minutes 1 of an inch lip ~ above the side the connects to the main receiver. Reduced "slots" in the PVC key receiver wherein the lips of the mag housing will slide right into to do the mag real estate flush v the receiver. Be sure to have actually this in the exactly spot ~ above the recipient or it will look kinda funny adhesive in place and let dry. The knob is make from a knob ns found. Ns think it come from one old set of bracket mount speakers. It"s the knob the holds the speaker in the bracket mount. The various other is a piece of plastic the was uncovered laying around.


I supplied thick Aluminum because that the extra detail parts. Cut them out through your Dremel and sand them to shape. Usage a file to clean them increase a bit. Making use of your Dremel reduced slots in the PVC the Epoxy lock in. Same with the trigger.


Now prime the hell out the it. Placed a few coats on. Then sand and also prep it and get it ready to paint. Prime, Prime, element can"t say it enough!


Paint it with level black spray paint. Then include coats that semi gloss clean coat. Paint and also install the urgent stock.




See more: Don T Tell Me How To Do My Job T, Stop Telling Me How To Do My Job

The final product! pick up some rubber griping product from www.blast-tech.com because that the rubber strips top top the barrel. It"s about $5.00 a foot and also you"ll require 4 feet.